Glass Splashback Installation in Dunedin
Window and Glass Repair Dunedin makes and fits glass splashbacks for kitchens, laundries and bathrooms. The glass is toughened, colour backed on the rear face, and cut to your kitchen with every power point, rangehood and tap penetration already in it before it is treated.
- Toughened and colour backed to any paint colour
- Templated on site, cut outs made before toughening
- One wipe surface with no grout lines
Get your free quote
Four quick questions. Most quotes come back the same day.
A splashback is one of the few pieces of glass in a house where the measurement has to be perfect. Toughened glass cannot be trimmed, drilled or notched after treatment, so every cut out is made first and the finished panel either fits or it does not. That is the whole job.
How the job runs
Four steps, and the order matters.
Template on site
We template after the benchtop is in and before you paint, because the glass follows the bench rather than the wall. Walls are rarely straight and a splashback that was measured off one will show a shadow gap at one end.
Colour matching
The colour goes on the back of the glass, so what you see is the paint through low iron glass. Standard float has a green cast that shifts pale colours noticeably, which is why whites and greys are almost always specified in low iron.
Cut outs before toughening
Power points, rangehood ducting, tap bodies and shelf brackets all get located and cut at this stage. Adding one afterwards means a new panel.
Fit and seal
Fitted on silicone with the bench edge sealed, and the panel is usually in and finished inside an hour once it is on site.
What glass splashbacks do well, and what they do not
They are a single continuous surface with no grout lines, they wipe clean, they take heat behind a gas hob when they are toughened, and they bounce light around a kitchen in a way tile cannot.
What they will not do is forgive a change of mind. There is no cutting a new hole, no shortening a panel and no drilling a shelf bracket. If a rangehood is moving, or the cabinetry is not final, wait. We would rather template twice than make a panel twice.
Timing it against the rest of the kitchen
Toughened and colour backed glass is made to order, so allow one to two weeks from template to fit. Booking us before the benchtop goes in does not help, because there is nothing accurate to template from.
The sequence that works: cabinetry in, benchtop fitted, we template, you paint, we fit. Plan the kitchen around that and nothing sits waiting.
Templating a splashback so it fits
Off the bench, not the wall
Walls are rarely straight and almost never plumb. A splashback measured off the wall will show a shadow gap at one end where the bench and the wall disagree.
We template off the finished benchtop, which is the line your eye actually reads, and scribe the top edge to the wall instead.
Sequence matters more than lead time
Cabinetry in, benchtop fitted, template, paint, fit. Booking a template before the benchtop is in wastes a visit, and painting after the glass is fitted means cutting in against glass you will then have to clean.
Allow one to two weeks between template and fit, and plan the rest of the kitchen around it.
The glass splashbacks process at Window and Glass Repair Dunedin in Dunedin
Supply and fit work is simple to describe and easy to get wrong at the measure, because nothing can be adjusted once the product is made.
Template at the measure
The opening is measured and anything that is not a plain rectangle is templated. Cut outs, apertures and irregular shapes are recorded then, because they cannot be added afterwards. In older Dunedin housing very little is truly square.
Agree the specification in writing
Product type, thickness, backing or mesh, edge finish and fixing method, all confirmed before anything is ordered so what arrives is what you expected.
Talk through the position
Where the product goes affects both cost and performance. Putting a pet door into a smaller fixed pane rather than a large slider panel means a smaller replacement pane and a lower price, and it is worth looking at every option in the room.
Specify for humidity where it applies
A mirror in a Dunedin bathroom needs a backing rated for moisture. Standard backing in a wet area with limited ventilation is the single most common reason we return to replace one within a few years.
Manufacture to order
Almost everything in this category is made to your measurements, so there is a real lead time. Window and Glass Repair Dunedin confirms the date rather than estimating it.
Fit, fix and adjust
Fitted square, fixed properly and adjusted so everything operates as it should. Window and Glass Repair Dunedin does not leave a product that functions but sits crooked.
Clean down and explain the care
Site cleared, product cleaned, and you get told how to look after it. Most of what shortens the life of these products is being cleaned with the wrong thing.
Getting the details right in Dunedin
Small jobs are where corners get cut, because nobody inspects them and the consequences take years to appear.
Humidity is the enemy of most of these products
Cold rooms, limited ventilation and long winters mean bathrooms and laundries here stay damp far longer than they would further north. Specification has to reflect that rather than defaulting to the cheapest option.
Old openings are rarely square
In Victorian and Edwardian housing the opening has moved with the building. Templating rather than measuring two dimensions is the difference between a clean fit and a visible gap down one side.
Screens make windows get opened
Where insects or a cat are the reason a window stays shut, a screen is the cheapest ventilation improvement available. In a damp house that matters more than it sounds.
Safety glazing still applies
A shower screen, a splashback beside a hob and a pet door in a slider panel are all positions with requirements. Window and Glass Repair Dunedin specifies to the standard rather than to what is quickest.
What glass splashbacks costs in Dunedin
Small supply and fit jobs are priced by the product and the measure, and the measure is where the cost is decided.
Made to order, always
Almost everything in this category is manufactured to your measurements, so the price follows the size and the specification rather than a catalogue. There is a real lead time and Window and Glass Repair Dunedin confirms the date rather than estimating it.
Where the position changes the price
Putting a pet door into a smaller fixed pane rather than a large slider panel means a much smaller replacement pane. Looking at every option in the room before choosing is often worth several hundred dollars.
Specification for wet areas
A mirror in a Dunedin bathroom needs a moisture rated backing, and a splashback beside a hob needs toughened glass. Standard product in a wet or hot position is the single most common reason we return within a few years.
Repair before replacement
A torn flyscreen in a sound frame is remeshed for a fraction of a new unit. The frame is the expensive part and it usually outlives several meshes, so Window and Glass Repair Dunedin quotes the remesh first.
Getting the specification right in Dunedin
Three decisions that are permanent once the product is made.
Edge finish and fixing method
A polished edge is clean and modern, a bevel reads traditional, and both are done at manufacture. Mechanical clips allow a mirror to be removed later, adhesive gives a cleaner look and is effectively permanent.
Mesh type on screens
Standard fibreglass for insects, heavier pet resistant mesh where a cat or dog pushes at it, and fine mesh where sandflies are a problem. Fine mesh lets less air through, which matters in a house you are ventilating to manage damp.
Safety glazing still applies
A shower screen, a splashback and a pet door cut into a slider panel are all positions with requirements under the standard. Window and Glass Repair Dunedin specifies to it rather than to whatever is quickest to source.
Glass Splashbacks at a glance
- Glass
- 6mm toughened, colour backed on the rear face
- Low iron option
- Recommended for whites, greys and pale colours
- Cut outs
- Power points, rangehood, taps and brackets, all before toughening
- Template
- On site after the benchtop is fitted, before painting
- Lead time
- One to two weeks from template to fit
- Fit time
- Usually under an hour on site
Glass Splashbacks in Dunedin: common questions
Can you match my paint colour?
Yes. The colour is applied to the back of the glass, and for pale colours we use low iron glass so the green cast of standard float does not shift it.
Can a power point be added after the splashback is in?
No. Toughened glass cannot be cut or drilled after treatment, so every penetration has to be located at template stage.
Is glass safe behind a gas hob?
Toughened glass is, and that is what we supply. Ordinary annealed glass is not.
Recent Dunedin jobs
Got three quotes for retrofitting the front of the house. Only ones who measured every opening and explained why the south facing rooms needed different glass. Fourteen windows over three days and the difference in the mornings is obvious.
Landlord here. Had four flats assessed before the inspections. Two just needed sashes freed up and stays replaced rather than new joinery, which saved me a fortune. Straight answers and a written report I could hand over.
Slider had been jamming for years and we assumed it needed replacing. Turned out to be rollers and a bent track. Two hours, a fraction of the price we were braced for.
Fogged unit in the lounge, measured on the Tuesday and in by the following Monday. Fair price and they cleaned up after themselves.
Get a price for glass splashbacks in Dunedin
Free measure, fixed written quote, and a straight answer on whether it needs repairing or replacing.
Start your quote
Four questions and you are done.